The SPN 2791 fault code indicates an issue with the Exhaust Gas Recirculation (EGR) system, typically found in medium and heavy-duty trucks like International and Freightliner models.
In our workshop, we've encountered Fault Code SPN 2791 quite frequently across various car makes. Just last week, a 2018 Volvo XC90 came in with reduced power and rough running. Sure enough, the scan tool revealed SPN 2791 FMI 7, indicating a mechanical fault with the EGR valve. We've seen similar issues on several Volkswagen Tiguans and Audi Q5s as well. It's not just limited to European makes, though – we've diagnosed SPN 2791 on Ram 2500 trucks and even a few Nissan Frontiers. From our experience, it seems that carbon buildup and sticking EGR valves are the most common culprits, regardless of the vehicle make. Cleaning the valve and passages usually resolves the issue, but in some cases, we've had to replace the entire valve assembly.
Urgency and Severity
When the SPN 2791 fault code appears, assess the severity:
- If accompanied by reduced engine power or rough running, stop driving and have the vehicle inspected by a qualified technician.
- In less severe cases, you may continue driving briefly, but address the issue promptly to prevent further damage.
Code Details
- SPN 2791 is a generic code applicable to various makes and models of medium and heavy-duty trucks.
- The code may have different Failure Mode Indicators (FMI) specifying the fault:
- FMI 7: Mechanical fault with the EGR valve
- FMI 13: EGR valve controller out of calibration
Parts Involved and Their Roles
The main component associated with SPN 2791 is the EGR valve, which controls the flow of exhaust gases back into the engine intake to reduce NOx emissions.
Common Causes
- Faulty EGR valve
- Clogged EGR passages or crossover tubes
- Wiring issues in the EGR valve circuit
- Bad delta-P sensor
- Wrong engine software/calibration
Diagnosing Steps
- Scan for additional fault codes, especially voltage faults (SPN 168).
- Check the "Reserved for Extreme Parameter" value in the extended data for SPN 2791 FMI 7.
- Inspect the EGR valve actuator pull rod and ball sockets for free movement. Replace if faulty.
- Measure the resistance of the EGR valve actuator motor coil. It should be 55-65 ohms.
- Check wiring and connectors between the EGR valve and Engine Control Module (ECM).
Solutions
- Clean or replace the EGR valve and passages.
- Replace faulty sensors like the delta-P sensor.
- Update engine software/calibration if incorrect.
- Repair wiring and connectors as needed.
Prevention
- Perform regular EGR system maintenance.
- Use high-quality fuel and oil.
- Avoid engine modifications that may affect EGR operation.
Repair Costs
- EGR valve replacement: $500-$1,000 (€425-€850)
- EGR system cleaning: $100-$300 (€85-€255)
- Labor costs: $100-$150 (€85-€130) per hour
Related Fault Codes
SPN 2791 may appear alongside other codes like:
Buy tested tuning file for Adblue / EGR / DPF / Adblue off now!
- SPN 2659: EGR Valve Position Sensor Circuit
- SPN 168 FMI (any): Voltage faults
Relevant specifications:
- EGR valve diameter: 50 mm (2 inches)
- EGR passage diameter: 25 mm (1 inch)
Frequently Asked Questions about SPN 2791 Fault Code
What does the SPN 2791 fault code mean?
SPN 2791 indicates an issue with the Exhaust Gas Recirculation (EGR) system, typically a malfunction with the EGR valve or its control circuit. The specific problem is determined by the Failure Mode Indicator (FMI) that accompanies the code.
What are the common FMIs associated with SPN 2791?
- FMI 7: Mechanical fault with the EGR valve, such as the valve being stuck open or closed.
- FMI 13: EGR valve controller is out of calibration. The valve failed its automatic calibration procedure at initial key-on.
What vehicles are affected by SPN 2791?
This generic code mainly affects medium and heavy-duty trucks, such as International, Freightliner, and Cummins-powered models.
What are the symptoms of an active SPN 2791 fault?
Symptoms may include:
- Illuminated amber “Check Engine” light
- Reduced engine power
- Rough running or misfires
- Disabled EGR valve actuation
Can I continue driving with SPN 2791?
It depends on the severity. If the code is accompanied by drivability issues, stop driving and have the vehicle inspected. Otherwise, you may drive briefly but address the problem promptly to prevent damage.
What causes SPN 2791 FMI 7?
A mechanical fault with the EGR valve, such as:
- Stuck or binding valve due to carbon buildup
- Faulty valve actuator motor or wiring
- Broken valve spring or damaged valve seat
What causes SPN 2791 FMI 13?
The EGR valve is detected more than 20% open during its automatic calibration at key-on, usually due to:
- Carbon deposits preventing full valve closure
- Faulty valve position sensor or wiring
- Incorrect ECM calibration
How do you diagnose SPN 2791?
- Scan for additional codes, especially SPN 168 voltage faults.
- Check the “Reserved for Extreme Parameter” value in the extended data for SPN 2791 FMI 7.
- Inspect the EGR valve actuator pull rod and ball sockets for free movement.
- Measure the resistance of the EGR valve actuator motor coil (should be 55-65 ohms).
- Check wiring and connectors between the EGR valve and ECM.
Can SPN 2791 be caused by issues other than the EGR valve?
Yes, it may result from:
- Clogged EGR passages or crossover tubes
- Faulty delta pressure (delta-P) sensor
- Incorrect engine software/calibration
- Other sensor problems that cause excessive EGR demand
How do you fix SPN 2791 FMI 7?
- Clean the EGR valve and passages thoroughly to remove carbon deposits.
- Replace the EGR valve and/or actuator motor if cleaning doesn’t restore proper operation.
- Repair damaged wiring or connectors.
How do you fix SPN 2791 FMI 13?
- Remove and thoroughly clean the EGR valve with carburetor cleaner. Lubricate if needed to free up valve movement.
- Replace the valve if cleaning doesn’t resolve the issue.
- Update the ECM with the correct software/calibration.
- Replace a faulty delta-P sensor.
Can I just clean the EGR valve to fix SPN 2791?
Cleaning the valve and passages is the first step and often resolves the issue. However, if the valve is physically damaged or the actuator has failed, replacement is necessary.
How much does it cost to fix SPN 2791?
- EGR valve replacement: $500-$1,000
- EGR system cleaning: $100-$300
- Labor: $100-$150 per hour
How can I prevent SPN 2791?
- Perform regular EGR system maintenance.
- Use high-quality fuel and oil to minimize carbon deposits.
- Avoid engine modifications that may affect EGR operation.
- Address other engine issues promptly.
What other components should I check with SPN 2791?
Inspect the delta-P sensor, crossover tubes, hoses, and wiring for damage or blockage. Look for excessive soot, fuel, coolant, or oil in the intake and exhaust that could foul the EGR system.
Can SPN 2791 cause damage if left unrepaired?
Yes, a stuck-open EGR valve can lead to:
- Rough running and misfires
- Excessive soot and smoke
- Clogged intake manifold and sensors
- Turbocharger failure
- Severe engine damage if hydrocarbons enter the cylinder
Is SPN 2791 related to any other fault codes?
It may appear alongside codes like:
- SPN 2659: EGR Valve Position Sensor
- SPN 168 FMI (any): Voltage faults
- SPN 4334: Delta-P Sensor
What are the dimensions of a typical EGR valve?
- Valve diameter: 50 mm (2 inches)
- Passage diameter: 25 mm (1 inch)
How does the EGR valve work?
The valve, operated by an electric actuator motor, opens to allow metered exhaust gas to enter the intake. This lowers combustion temperatures to reduce NOx emissions. The valve closes via spring force when not actuated.
What special tools are needed to diagnose SPN 2791?
A professional scan tool or dealer-level diagnostic software is recommended to read extended fault data, view live sensor values, and command the EGR valve for testing. A digital multimeter is needed for electrical checks.