P24B6 – Particulate Filter Temperature Sensor Circuit Low

POSTED IN pcodes

Updated on:

Urgency and Drivability

The P24B6 code, indicating a Particulate Matter (PM) Sensor Heater Control Circuit High condition, is generally not an immediate threat to vehicle drivability. However, it should not be ignored as it may lead to more severe issues if left unaddressed. Vehicles can typically be driven with this code present, but it's advisable to have the issue diagnosed and repaired as soon as possible.

In our workshop, we've noticed a significant increase in P24B6 codes across various European diesel models, particularly in Volkswagen, BMW, and Mercedes-Benz vehicles. While it's not exclusive to these brands, we've seen it more frequently in Euro cars compared to American or Asian makes. The code often appears in conjunction with other PM sensor-related issues, especially in vehicles with higher mileage or those subjected to frequent short trips. We've found that in many cases, the problem stems from a faulty PM sensor or damaged wiring rather than actual exhaust system issues. Interestingly, we've observed that vehicles regularly driven on longer journeys tend to experience this problem less frequently, likely due to the sensor reaching and maintaining optimal operating temperatures more consistently.

Potential risks of continued operation include:

  • Reduced fuel efficiency
  • Increased emissions
  • Potential damage to the exhaust system components
  • Risk of failing emissions tests

Detailed Code Information

P24B6 is a powertrain code related to the vehicle's emissions control system. Specifically, it indicates that the Engine Control Module (ECM) has detected a high voltage condition in the PM sensor heater control circuit.

This code is generally manufacturer-specific, meaning its exact interpretation may vary slightly between different vehicle makes and models. It's commonly found in diesel-powered vehicles equipped with particulate filters, including but not limited to:

Buy tested tuning file for Adblue / EGR / DPF / Adblue off now!

Register Now or Already have an account,

  • Mitsubishi L200/Triton
  • Various GM models (Chevrolet, GMC, Cadillac)
  • Some BMW and Mercedes-Benz diesel models

Components Involved

The Particulate Matter (PM) sensor is a crucial component of modern diesel emissions control systems. It's typically located after the Diesel Particulate Filter (DPF) in the exhaust system.

PM Sensor: This device measures the amount of particulate matter in the exhaust gases, providing feedback to the ECM about the efficiency of the DPF.

PM Sensor Heater: The heater is an integral part of the PM sensor. It maintains the sensor at an optimal operating temperature, ensuring accurate readings across various ambient conditions and exhaust temperatures.

These components play a vital role in monitoring and controlling exhaust emissions, helping vehicles meet stringent environmental regulations.

Common Causes

Several factors can trigger the P24B6 code:

  1. Faulty PM sensor: The sensor itself may be defective, providing incorrect readings to the ECM.
  2. Damaged wiring: Frayed, corroded, or damaged wiring in the PM sensor circuit can cause voltage irregularities.
  3. Connector issues: Loose, corroded, or damaged connectors can lead to poor electrical connections.
  4. ECM malfunction: In rare cases, the ECM itself may be faulty, misinterpreting signals from the PM sensor.
  5. Exhaust leaks: Leaks in the exhaust system can affect the PM sensor's readings.

Diagnostic Procedure

  1. Connect an OBD-II scanner and confirm the P24B6 code.
  2. Check for other related codes that may provide additional context.
  3. Inspect the PM sensor and its wiring for visible damage or corrosion.
  4. Use a multimeter to check the voltage at the PM sensor connector. Compare readings to manufacturer specifications.
  5. Inspect the exhaust system for leaks, particularly around the DPF and PM sensor.
  6. If available, use manufacturer-specific diagnostic software for more detailed analysis.

Tools required: OBD-II scanner, multimeter, manufacturer-specific diagnostic software (if available).

Solutions and Repair Options

  1. Replace the PM sensor if found faulty.
  2. Repair or replace damaged wiring or connectors.
  3. Update ECM software if recommended by the manufacturer.
  4. In rare cases, ECM replacement may be necessary.

DIY repairs are possible for experienced mechanics, but professional diagnosis is recommended due to the complexity of modern diesel emissions systems.

Prevention Strategies

  1. Regular maintenance of the exhaust system, including the DPF.
  2. Use high-quality diesel fuel to minimize particulate buildup.
  3. Avoid short trips that prevent the exhaust system from reaching optimal operating temperature.
  4. Address any exhaust leaks promptly to prevent contamination of the PM sensor.

Cost Analysis

Repair costs can vary significantly depending on the root cause:

  • PM sensor replacement: $200-$600 USD (€170-€510 EUR)
  • Wiring repair: $100-$300 USD (€85-€255 EUR)
  • ECM replacement (rare): $500-$2000 USD (€425-€1700 EUR)

Labor costs typically range from $100-$200 USD (€85-€170 EUR) per hour, with diagnostic time often billed separately.

Repair Guide

  1. Ensure the vehicle is cool and on a level surface.
  2. Locate the PM sensor in the exhaust system, typically after the DPF.
  3. Disconnect the battery to prevent electrical shorts.
  4. Unplug the electrical connector from the PM sensor.
  5. Remove any heat shields or obstructions to access the sensor.
  6. Unscrew the PM sensor from the exhaust pipe (may require a special socket).
  7. Install the new sensor, ensuring proper torque specifications are followed.
  8. Reconnect the electrical connector and battery.
  9. Clear the diagnostic codes and perform a test drive to confirm the repair.

Safety precautions: Wear gloves and eye protection. Be cautious of hot exhaust components.

P24B6 may occur alongside other PM sensor-related codes:

  • P24B0: PM Sensor Circuit Low
  • P24B1: PM Sensor Circuit High
  • P24B3: PM Sensor Heater Control Circuit Low
  • P24B4: PM Sensor Heater Control Circuit Open

These codes often indicate similar issues with the PM sensor or its circuit.

Technical Specifications

  • PM Sensor operating temperature: Typically 100-300°C (212-572°F)
  • Heater circuit voltage: Usually 12V or 24V, depending on the vehicle
  • Heater resistance: Varies by manufacturer, typically 2-10 Ω at 20°C (68°F)

Always refer to manufacturer-specific data for exact specifications, as these can vary between vehicle models and sensor designs.

Frequently Asked Questions About P24B6

What does the P24B6 code mean?

P24B6 indicates that the Engine Control Module (ECM) has detected a high voltage condition in the Particulate Matter (PM) sensor heater control circuit.

Is it safe to drive with the P24B6 code?

While not immediately dangerous, it’s advisable to have the issue diagnosed and repaired soon to prevent potential damage to the exhaust system and avoid increased emissions.

What causes the P24B6 code?

Common causes include a faulty PM sensor, damaged wiring, connector issues, ECM malfunction, or exhaust leaks.

How urgent is it to address the P24B6 code?

While not an emergency, it should be addressed promptly to maintain proper emissions control and prevent potential damage to related components.

What vehicles commonly experience the P24B6 code?

This code is typically found in diesel-powered vehicles equipped with particulate filters, including various makes and models.

How is the P24B6 code diagnosed?

Diagnosis involves using an OBD-II scanner, inspecting wiring and connectors, and checking voltage readings at the PM sensor.

Can I diagnose and fix P24B6 myself?

While possible for experienced mechanics, professional diagnosis is recommended due to the complexity of modern diesel emissions systems.

What tools are needed to diagnose P24B6?

An OBD-II scanner, multimeter, and possibly manufacturer-specific diagnostic software are required.

How much does it cost to repair P24B6?

Repair costs can range from $200 to $2000 USD, depending on the root cause and necessary repairs.

What components are involved in the P24B6 code?

The main components are the Particulate Matter sensor, its heater, and the associated wiring and connectors.

How does the PM sensor heater work?

The heater maintains the PM sensor at an optimal operating temperature to ensure accurate readings across various conditions.

What are the symptoms of P24B6?

Symptoms may include reduced fuel efficiency, increased emissions, and illumination of the Check Engine Light.

Can P24B6 cause damage if left unaddressed?

Yes, it can potentially lead to damage in the exhaust system components and cause the vehicle to fail emissions tests.

Are there any related codes to P24B6?

Yes, related codes include P24B0, P24B1, P24B3, and P24B4, which also pertain to PM sensor issues.

How can I prevent P24B6 from occurring?

Regular maintenance of the exhaust system, using high-quality diesel fuel, and addressing exhaust leaks promptly can help prevent this issue.

What’s the difference between P24B6 and other PM sensor codes?

P24B6 specifically indicates a high voltage in the heater control circuit, while other codes may indicate low voltage or open circuits.

How long does it take to repair P24B6?

Diagnosis typically requires about 1 hour, with repair time varying based on the specific issue.

Can P24B6 be cleared without repairs?

While the code can be cleared, it will likely return if the underlying issue isn’t addressed.

What are the technical specifications for the PM sensor?

Specifications vary by manufacturer but typically include operating temperatures of 100-300°C and heater circuit voltages of 12V or 24V.

How does P24B6 affect vehicle emissions?

It can lead to increased emissions as the PM sensor may not accurately measure particulate matter, potentially affecting the DPF’s operation.

Buy tested tuning file for Adblue / EGR / DPF / Adblue off now!

Register Now or Already have an account,

Related posts