P2106 – Throttle Actuator Control System – Forced Limited Power

What is Code P2106?

P2106 is a generic powertrain diagnostic trouble code that indicates the engine control module (ECM) has detected a major failure in the throttle actuator control system and has gone into a "forced limited power" mode, also known as "limp mode" or "fail-safe mode". This code is triggered when the ECM receives abnormal signals from various throttle control components.

Severity and Symptoms

Code P2106 itself is considered moderately severe, as it indicates the ECM has significantly limited engine power output as a precautionary measure. Continuing to drive with this code active is possible but not advisable, as performance will be very limited (e.g. unable to exceed 48-64 km/h or 30-40 mph). Other drivability issues like rough running, stalling, or no-start may also be present. It's best to diagnose and repair the underlying issue promptly.

Common symptoms include:

• Illuminated Check Engine Light
• Reduced engine power, acceleration, and top speed
• Rough running or misfiring
• Stalling or difficulty starting

Applicable Vehicles

P2106 is a generic code that can occur on any vehicle with an electronic throttle control system, which includes most passenger cars and light trucks made from 1996 onward. The specific components and failure modes may vary between makes and models.

Parts Involved

The main components of the electronic throttle control system include:

• Accelerator Pedal Position (APP) Sensor – Measures accelerator pedal position and sends signal to ECM
• Throttle Position Sensor (TPS) – Measures throttle plate angle and sends signal to ECM
• Throttle Actuator (Motor) – Opens and closes the throttle plate as commanded by the ECM
• Engine Control Module (ECM) – Controls the throttle actuator based on APP sensor input and various other factors

Common Causes

Potential causes of a P2106 code include:

1. Faulty APP sensor (e.g. due to wear, contamination, wiring issues)
2. Faulty TPS (e.g. due to wear, contamination, wiring issues)
3. Faulty throttle actuator motor
4. Obstructed or sticking throttle body
5. Corroded or damaged wiring and connectors
6. Faulty ECM (rare)

Diagnosis Steps

1. Scan for codes, document freeze frame data
2. Visually inspect throttle body and wiring
3. Test APP sensor operation and signals
4. Test TPS operation and signals
5. Test throttle actuator motor operation
6. If no issues found, suspect ECM fault

Repair Options

• Clean throttle body if dirty/sticking
• Replace faulty APP sensor
• Replace faulty TPS
• Replace faulty throttle actuator motor
• Repair damaged wiring or connectors
• Replace ECM if faulty (rare)

Prevention

• Regular throttle body cleaning (every 50,000-100,000 km or 30,000-60,000 mi)
• Avoid aftermarket "performance chips" that alter throttle mapping
• Address other codes promptly, as P2106 can be triggered secondarily

Cost to Diagnose and Repair

• Diagnosis: 1-2 hours labor ($100-$250 USD, €90-€225 EUR)
• Throttle body cleaning: 0.5 hours labor ($50-$125 USD, €45-€110 EUR)
• APP sensor: $75-$300 USD (€70-€270 EUR) plus 0.5-1 hours labor
• TPS: $50-$200 USD (€45-€180 EUR) plus 0.5-1 hours labor
• Throttle actuator: $300-$650 USD (€270-€585 EUR) plus 1-2 hours labor
• ECM: $500-$1500 USD (€450-€1350 EUR) plus 1-2 hours labor

Related Codes

Other codes that may appear along with P2106 include:

• P0121-P0124 (TPS faults)
• P0221-P0228 (APP sensor faults)
• P0506 (Idle RPM lower than expected)
• P0507 (Idle RPM higher than expected)
• P1516 (Throttle actuator control module)
• P2101-P2103, P2110-P2112 (Other throttle actuator faults)

In summary, P2106 indicates a serious failure in the electronic throttle control system that requires prompt diagnosis and repair to restore proper performance and drivability. Methodical testing of the APP sensor, TPS, throttle actuator, and wiring can pinpoint the faulty component in most cases. As always, following the manufacturer's diagnostic and repair procedures for the specific vehicle is recommended.

Frequently Asked Questions about P2106 Code

What does the P2106 code mean?

P2106 is a generic powertrain diagnostic trouble code that indicates the engine control module (ECM) has detected a major failure in the throttle actuator control system and has gone into a "forced limited power" mode, also known as "limp mode" or "fail-safe mode". This code is triggered when the ECM receives abnormal signals from various throttle control components.

How serious is code P2106?

Code P2106 itself is considered moderately severe, as it indicates the ECM has significantly limited engine power output as a precautionary measure. Continuing to drive with this code active is possible but not advisable, as performance will be very limited (e.g. unable to exceed 30-40 mph). It's best to diagnose and repair the underlying issue promptly.

What are the common symptoms of P2106?

Common symptoms of P2106 include:

• Illuminated Check Engine Light
• Reduced engine power, acceleration, and top speed
• Engine may enter "limp mode" with significantly reduced performance
• Rough running or misfiring
• Stalling or difficulty starting

What are the potential causes of code P2106?

Potential causes of a P2106 code include:

1. Faulty accelerator pedal position (APP) sensor
2. Faulty throttle position sensor (TPS)
3. Faulty throttle actuator motor
4. Obstructed or sticking throttle body
5. Corroded or damaged wiring and connectors
6. Faulty engine control module (ECM)

Can I still drive with a P2106 code?

While it may be possible to continue driving with a P2106 code active, it is not recommended. The vehicle will have significantly reduced power and acceleration, making driving difficult and potentially unsafe. It's best to diagnose and repair the issue as soon as possible.

How do you diagnose the cause of code P2106?

To properly diagnose the cause of P2106, a mechanic should:

1. Scan for all codes and document freeze frame data
2. Visually inspect the throttle body, sensors, and wiring for damage
3. Test the APP sensor, TPS, and throttle actuator motor operation
4. If no obvious faults are found, suspect an issue with the ECM

What parts are involved with the P2106 code?

The main components involved with the P2106 code are:

• Accelerator pedal position (APP) sensor
• Throttle position sensor (TPS)
• Throttle actuator motor
• Throttle body assembly
• Engine control module (ECM)
• Associated wiring and connectors

How much does it cost to diagnose and fix code P2106?

The cost to diagnose and repair a P2106 code can vary depending on the root cause. Typical costs may include:

• Diagnostic fee: $75-$150
• Throttle body cleaning: $50-$100
• APP sensor replacement: $100-$300
• TPS replacement: $75-$200
• Throttle actuator motor replacement: $300-$750
• ECM replacement: $500-$1500

Can a bad throttle body cause the P2106 code?

Yes, a faulty or obstructed throttle body can trigger the P2106 code. If the throttle plate is sticking or if the throttle body is excessively dirty, it can cause abnormal signals to the ECM resulting in the forced limited power mode.

Can a weak battery cause code P2106?

While a weak battery itself is unlikely to directly cause a P2106 code, it can lead to other issues that may trigger it. Low voltage can cause abnormal sensor readings or ECM malfunctions which could potentially set the code.

Will disconnecting the battery clear the P2106 code?

Disconnecting the battery may temporarily clear the P2106 code from the ECM's memory. However, if the underlying problem is not fixed, the code will likely reappear once the fault is detected again. It's important to properly diagnose and repair the root issue.

Can low oil cause the P2106 code?

Low engine oil is not a direct cause of the P2106 code. This code is related to the electronic throttle control system and is not typically affected by oil level or pressure.

How do you fix code P2106?

To fix code P2106, a mechanic will need to diagnose the root cause and repair or replace the faulty component. This may involve:

• Cleaning the throttle body if dirty or sticking
• Replacing a faulty APP sensor, TPS, or throttle actuator motor
• Repairing damaged wiring or connectors
• Replacing the ECM if faulty

Can a vacuum leak cause the P2106 code?

A vacuum leak is not a common direct cause of the P2106 code. However, a major vacuum leak can potentially cause drivability issues and abnormal sensor readings that could indirectly lead to the code being set.

Can a clogged catalytic converter cause code P2106?

A clogged catalytic converter is unlikely to directly cause a P2106 code, as this code is specific to the electronic throttle control system. However, a severely restricted catalytic converter can cause drivability issues and abnormal exhaust backpressure which may indirectly contribute to the code being triggered.

How long does it take to fix code P2106?

The time required to fix a P2106 code can vary greatly depending on the root cause. Simple repairs like cleaning the throttle body may take less than an hour, while more involved repairs like replacing the throttle actuator or ECM could take several hours.

Is code P2106 the same as reduced engine power?

Code P2106 is closely related to reduced engine power, as it indicates the ECM has intentionally limited throttle output as a safety measure. When this code is triggered, the engine will go into a "reduced power" or "limp home" mode to prevent further damage.

Can a bad mass air flow sensor cause the P2106 code?

A faulty mass air flow (MAF) sensor is not a common direct cause of the P2106 code. However, a MAF sensor issue can cause drivability problems and abnormal readings that may indirectly contribute to the code being set in some cases.

Can a bad O2 sensor cause code P2106?

A faulty O2 sensor is unlikely to directly cause a P2106 code, as this code is specific to the electronic throttle control system. However, an O2 sensor issue can cause poor engine performance and abnormal fuel trim readings which may indirectly trigger the code in rare cases.

What is the difference between code P2106 and P2135?

While both P2106 and P2135 are related to the electronic throttle control system, they indicate different specific faults:

• P2106 indicates the ECM has detected a major fault and has gone into a forced limited power mode.
• P2135 indicates there is a problem with the throttle position sensor (TPS) circuit, such as a short, open circuit, or abnormal voltage reading.

In summary, code P2106 indicates a serious issue with the electronic throttle control system that has caused the ECM to limit engine power output as a safety precaution. Promptly diagnosing and repairing the root cause is important to restore proper vehicle performance and prevent further damage. If you suspect your vehicle has triggered a P2106 code, it's best to have it inspected by a qualified mechanic as soon as possible.